Submersible bore pumps - Single phase 1.5hp 1100watt single phase bore pumps Payments for your pump can be made by Paypal, Credit Card or Direct Debit

< back

You are here > Home > Bore Pumps > 1 Hp Single Phase Bore Pump

Telephone support
Contact Us

 

“Good Old-fashioned friendly service and advice”
-Mark (VIC)

 

 

Single phase 1.5hp submersible bore pump dimensions

Pump Dimensions:
L1 = 409
L = 820
DN = 2 "
Max = 96mm

 

Search Query
Menu
Home
 
Bore Pumps
Bore Pumps
3" Submersible Pumps
4" Submersible Pumps
Submersible Motors
Solar Pumps
 
Sewage Pumps
Septic Tank Pumps
Greywater Pumps
 
Pressure Pumps
Pressure Pumps
Franklin Pressure Pumps
Rainwater Tank Pumps
Automatic Pump Control
Pressure Pump Accessories
Self-Priming Pressure Pumps
 
Other Pumps
Pool Pumps
Saltwater Pump
Peripheral Pump
Garden Pump
Convertible Jet Pump
Engine Drive Transfer Pumps
Fire Fighting Pumps
Generators / Gensets
 
Accessories
Bore Pump Accessories
Bore Pump Control Box
Bore Pump Switch
Pressure Pump Controller
Pressure Tanks
Variable Speed Pump Controller
Inline Constant Pressure System
 
Helpful Info
Installing a Bore Pump
Pump Direct from Bore to House

 

     
  I pay for shipping  
Free delivery of your pump anywhere in Australia

 

1 Hp / 0.75 Kw / 5 Stage / 4 Inch Single Phase Bore Pumps

 

Submersible 1Hp 0.75 kw 5 stage single phase deep bore water pump

 

 


 

Single Phase Submersible Water Bore Pump

Pump Specification;

  • Item Number: 4COVSPM8-5
  • Suitable for 4" or 6" Bore Casing
  • Power Rating: 1HP / 0.75KW
  • Voltage: Single Phase 240V / 50Hz
  • Full Load Run Amps : 5.6A (save money in cable)
  • Locked Rotor Amps: 19A
  • Max Submergence 350m
  • Water Flow (259,000L/day)
  • Max Delivery Capacity 10 800L/H in (10M head)
  • Outlet: 40mm / 2 inch
Litres per minute Litres per second Depth of Bore or Well
0 lpm 0 lps 27m
30 lpm 0.50 lps

25m

60 lpm 1.00 lps 23m
90 lpm 1.50 lps 21m
120 lpm 2.00 lps 18m
150 lpm 2.50 lps 14m
180 lpm 3.00 lps 10m

View Flow Chart

The water supply can be tapered back by a tap fitted at the top of the bore.

Purchase Pump $850

 

1 Phase Starter / Control Boxes
kW Description Volts   Model No Order No Price Buy
  control boxes and starter box  
0.75 230 PSC QCAVE100 053 AH 04 AC501 $165
 

IMPORTANT

A matching kW rating Coverco Control Box must be used with each single phase 230V motor or warranty is void

 

Coverco submersible motor

Italian made motor

 

control boxes and starter box

12 months Warranty on wet end

2 year Coverco Motor Warranty

 

The Coverco range of bore pumps from Pentax have a PSC Motor which gives a lower starting current making it ideal for use with a Generator or even a Solar System.

 

This pump is suitable for a bore casing larger than 100mm in diameter as the pump diameter including the cable guard is 96mm. You would need to allow a few millimeters on either side of the pump for water to flow past the pump. It can also be used with a 5" or 6 " 150mm bore casing. If it is to be used in a 5 " or 6 " bore casing, it is recommended that you shroud the pump. This helps keep the motor cool. This pump is best suited to bores varying from 10m deep to 25 m deep. Designed for domestic clean water use.

Coverco 4" oil lubricated submersible motors and controls have been supplied into Australia as the premium oil lubricated motor for over 15 years and have been installed extensively over that time.

Coverco offer you a lower cost product to compete against other oil lubricated motors.

The Coverco 4" lubricated motors and controls are priced very competitively for you.

  • Single and three phase
  • 0.37 to 7.5kW
  • Maintenance Free
  • Low and High Thrust Models
  • Enamel insulated wire wound stator
  • FDA approved non toxic lubricating fluid
  • 304SS outer shell
  • Mechanical Seal with Sand Slinger

Control Boxes

  • Polycarbonate IP56
  • 0.37 to 3.7kW
  • On indicator
  • Overload Protection
  • Rocker switch or On/Off switch


submersible coverco motor

Coverco pump motor

Need to reduce the water flow? A bore tap is used to reduce the flow of water that the bore pumps
If less water is needed, the water flow can be throttled back by assembling a tap at the top of the bore. However, if you do need to reduce the flow by a considerable amount, you may need to shroud the pump.
 

What size submersible cable do I need?

This chart is just a guide to help you get an idea of cable size. It is recommended that your local electrical supply outlet do your cable selection for you.

Cable length in meters from motor to control box Cable size
From 0 to 25 meters 4 wire x 1mm2
from 25m to 40m 4 wire x 1.5mm2
from 40m to 65m 4 wire x 2.5mm2
from 65m to 105m 4 wire x 4mm2
from 105m to 160m 4 wire x 6mm2
from 160m 4 wire x 10mm2
 

Demand feed from bore to house or garden without using a water tank

It is also possible to pump water directly to the garden / house without having to pump into a water tank.

For more information on pumping directly to the house or garden click here

Using a submersible bore pump to pump on demand from the bore or well to the house and garden
 
 
Delivery Australia Wide includes: NT, Northern Territory, Darwin, WA, Western Australia, Perth, SA, South Australia, Adelaide, Qld, Queensland, Brisbane, Cairns, NSW, New South Wales, Sydney, ACT, Australian Capital Territory, Canberra, Vic, Victoria, Melbourne, Tas, Tasmania, Hobart and all minor cities and towns.